ブックタイトル切削工具総合カタログ　│　岡崎精工株式会社

概要

切削工具総合カタログ　│　岡崎精工株式会社

全品即納195Data技 術 資 料ノンコートエンドミル：推奨切削条件　Recommended Milling Conditions for non-coated Endmills被削材Work Material切削速度Cutting Speed一般構造用鋼・炭素鋼・合金鋼・調質鋼Structural Steels, Carbon Steels, Alloy Steels, Hardened SteelsSS400,S55C,SCM,SK,SKD鋳鉄Cast IronFC軟質アルミ合金Aluminum AlloysA1200,A2024切込条件40?50m/min Condition of milling?20HRC回転数Spindle Speed(rpm)送りFeed（mm/min）35 ?45m/min?30HRC回転数Spindle Speed(rpm)送りFeed（mm/min）25 ?35m/min?40HRC回転数Spindle Speed(rpm)送りFeed（mm/min）40 ?50m/min回転数Spindle Speed(rpm)送りFeed（mm/min）65 ?80m/min回転数Spindle Speed(rpm)送りFeed（mm/min）SED2124681016202530apae14,3007,2003,6002,4001,8001,40090072057048010011011015017018020019018017012,1006,1003,0002,0001,5001,200760610480400607070901001101201101101009,6004,8002,4001,6001,2001,0006004803803203030304040505050504014,3007,2003,6002,4001,8001,40090072057048013014014018022023025023023021022,30011,1005,6003,7002,8002,2001,3901,1108907402402602603404004304604404203900.5DD0.5DD0.5DD0.5DD0.5DDSED2MSED2LSCD2346810121620apae4,2003,2002,1001,6001,3001,10080064080801001201301301101003,6002,7001,8001,4001,10090068054050507080909070702,9002,1001,4001,10090070054043020203030404030304,2003,2002,1001,6001,3001,1008006401101101401701801901501406,7005,0003,3002,5002,0001,7001,2501,0002002102603203403502902700.5DD0.5DD0.5DD0.5DD0.5DDSEE3（溝切削）(Slotting)345681012apae4,8003,6002,9002,4001,8001,4001,2001401501602002302402504,0003,0002,4002,0001,5001,2001,0008090901201301401503,2002,4001,9001,6001,2001,000800304040506060604,8003,6002,9002,4001,8001,4001,2001701902002502803003207,4005,6004,5003,7002,8002,2001,9003203603704705305605900.5DD0.5DD0.5DD0.5DD0.5DDSEE3（側面切削）(Side Milling)345681012apae4,8003,6002,9002,4001,8001,4001,2002102302403003403603804,0003,0002,4002,0001,5001,2001,0001201401401802002102203,2002,4001,9001,6001,2001,000800506060808090904,8003,6002,9002,4001,8001,4001,2002602903003804204504707,4005,6004,5003,7002,8002,2001,9004805405607107908408801.5D0.2D1.5D0.2D1.5D0.2D1.5D0.2D1.5D0.2DSED424681016202530apae7,2003,6002,4001,8001,4009007205704803303404405305605905605404906,1003,0002,0001,5001,2007606104804002002002603103303503303202904,8002,4001,6001,2001,00060048038032080901101301401501401301207,2003,6002,4001,8001,40090072057048041043054066071074070067061011,1005,6003,7002,8002,2001,3901,1108907407707901,0201,2301,3201,3901,3101,2501,1401.5D0.2D1.5D0.2D1.5D0.2D1.5D0.2D1.5D0.2DSED4M34681012apae4,8003,6002,4001,8001,4001,2001902002403503804004,0003,0002,0001,5001,2001,0001101201402102202303,2002,4001,6001,2001,00080050506090901004,8003,6002,4001,8001,4001,2002402503004404705007,4005,6003,7002,8002,2001,9004504705608308909302.0D0.2D2.0D0.2D2.0D0.2D2.0D0.2D2.0D0.2DSEE46810121620apae2,4001,8001,4001,2009007203604104304504804502,0001,5001,2001,0007606102102402602702802701,6001,2001,000800600480901001101101201102,4001,8001,4001,2009007204505105405706005603,7002,8002,2001,9001,3901,1108509501,0101,0601,1101,0501.5D0.2D1.5D0.2D1.5D0.2D1.5D0.2D1.5D0.2D溝切削SlottingDap注1） 切込み量が上記を超えるときは、送りを20 ?30％落としてください。If the cutting depth is large,reduce thefeed rate by approximately 20% to 30%.注2） 機械、チャックは剛性のある精度の高いものをご使用ください。Use a rigid and precise machine andholder.注3） 切削油は被削材に適したものを選定してください。Use a suitable cutting fluid.注1） 切込み量が上記を超えるときは、送りを20 ?30％落としてください。If the cutting depth is large,reduce thefeed rate by approximately 20% to 30%.注2） 機械、チャックは剛性のある精度の高いものをご使用ください。Use a rigid and precise machine andholder.注3） 切削油は被削材に適したものを選定してください。Use a suitable cutting fluid.注4） Z 軸方向の送りは横送りの1/3 以下にしてください。When axial feed, please use 1/3 of amount ofradial feed.apae側面切削Side Milling品番Product Code.寸法Size