ブックタイトル切削工具総合カタログ │ 岡崎精工株式会社

ページ
188/212

このページは 切削工具総合カタログ │ 岡崎精工株式会社 の電子ブックに掲載されている188ページの概要です。
秒後に電子ブックの対象ページへ移動します。
「ブックを開く」ボタンをクリックすると今すぐブックを開きます。

ActiBookアプリアイコンActiBookアプリをダウンロード(無償)

  • Available on the Appstore
  • Available on the Google play

概要

切削工具総合カタログ │ 岡崎精工株式会社

186Data技 術 資 料技術資料 Dataハイス(SKH51 相当品)High speed steels(SKH51)MCO(コバルト高速度鋼)MCO(Cobalt high speed steels)超硬Cemented carbide■切削条件の求め方 How to decide cutting conditions(1)切削速度(V)と回転数(N)  Cutting speed(V) and spindle speed(N) 切削速度(または周速)(V)は、一般に工具材種と被削材の種類で決まります。工具材種別には通常、表1 の範囲で選びます。The cutting speed is dependent on tool material grade and the kind of work material. The cutting speed is usually selected within the range given in Table 1by tool grade. (表1)材種別切削速度(V) (Table. 1) Cutting speed by material grade被削材の被削性が良い場合、切り込みの少ない場合、切削油を十分使用できる場合は切削速度を高めに選びます。被削性が不明なときは、下限に近い値からスタートするのが安全です。回転数(N)は、切削速度と使用する工具の刃径から上式により計算します。組み合わせカッターなどでは、最大直径を基準に計算して下さい。尚、本紙に掲載された切削条件表の回転数は、推奨切削速度の中間値について算出したものです。When work material has excellent workability, when there is little depth of cut, or when sufficient cutting fluid can be used, select rather high cutting speed.When work ability of work material is unknown, it is safe to try rearly the lowest cutting speed at first, and then increase the speed gradually.The revolution nummber(N)is calculated by the following formula using cutting speed and outside diameter of the tool to be used.In the combination cutter etc., calculate based on the maximum diameter.The revolution nummber given in the Table of cutting conditions was calculated by using the intermedicate value of recommended cutting speeds.(2)送り速度(F)と1 刃当り送り(f)  Feed speed(F)and feed per tooth(f)作業能率は、テーブルの送り速度(F)で決まりますが、切削条件は1 刃当り送り(f)を先に定めます。工具の大きさ(外径と刃厚)、刃数、被削材の被削性、加工精度、機械剛性などを考慮して決定します。表2 を目安として示しますが、外径の割に幅や穴径の小さい場合、カラー径が小さい場合やサポート間隔の広い場合などでは、小さめに、千鳥刃やネジレ刃では大きめに調整して下さい。Working efficiency is determined by the table speed(F), but the feed per tooth should be fixed first of all in setting cutting conditions.Other conditions should be determined considering dimension of a tool(outside diameter and width), number of teeth, machinability of work material,machining precision, and machine rigidity. Target values are shown in Table 2. Select a little low value within the range, when width or bore diameter is toosmall compared with outside diameter, when diameter of a collar is small, or when supporting interval is large.As for staggered tooth or helical tooth, select a little high value within the range. (表2)1 刃当り送り(f)(Table. 2) Feed per tooth(f)(3)切込み  Depth of cut切込みは、基本的には取り代の大きさで決まります。広い幅を切削する場合は、機械の馬力や剛性を考慮に入れて、切込みを小さくします。メタルソー等で深溝切削になる場合は、工具に無理な力が掛からないよう、切削速度と送り速度を控えめにして下さい。Depth of cut is basically determined by the size of machining allowance.When cutting wide area, perform cutting with small depth of cut considering horsepower and stiffness of the machine. In deep grooving by using a metal slitting saw and the like, select a little low cutting speed and the feed speed so thattoo much force may not be applied on the tool.V = 15 ?25m/minV = 15 ?30m/minV = 30 ?60m/minN = 1000 × V    π × DN:回転数 min-1N:Spindle speed, min-1V:切削速度 m/minV:Cutting speed, m/minD:刃径 mmD:Outside diameter, mmπ:円周率(3.14)π : Ratio of circumference of acircle to its diameter(3.14)サイドカッターSide milling cutters f = 0.03 ?0.06千鳥刃サイドカッターStaggered side milling cutters f = 0.06 ?0.10メタルソーMetal slitting saws f = 0.02 ?0.04F = f × Z × NF:送り速度 mm/minF:Feed speed, mm/minf:1 刃当り送り mm/toothf:Feed per tooth, mm/toothZ:刃数Z:Nummber of teethN:回転数 min-1N:Spindle speed, min-1